Need help?
1.800.999.3483 ⮟
|
STORE FINDER
Retail Locations
|
Brands |  Current Specials |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4.5
5.0
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. Th
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
The Nomad Ray can be easily adjusted to comfortably fit all body types. The independently adjustable harness design can be quickly set up for any diver. Shoulder and waist webbing can be replaced independently if damaged or trimmed too short. The Nomad Ray uses a fast, tool-free bungee length adjustment system. Simply pull to the desired length, tie a single overhand knot, and tuck the excess into the integrated sleeve. A quick-adjust belly band with a custom molded bungee hook keeps the wing wrapped snugly around the diver’s body. The Nomad Ray utilizes custom designed stainless steel hardware pieces including the waist transition plates, drop down D-rings, sliding D-rings, bungee retention slides, and a dog bone crotch strap double D-ring for a bonus place to clip off accessories. A zipper on the inside of the Nomad Ray wing allows for access to three integrated weight pockets capable of holding up to five pounds of each of hard or soft weight. This design maintains the lowest profile possible while providing quick access for the diver to add trim weights or adjust mission-specific weighting. Padded pocket walls add protection and comfort for the diver’s back. A sixteen-inch corrugated inflation hose gives the diver multiple mounting options to keep the inflator close at hand. The hose can easily be swapped from the left side to the right side of the wing according to diver preference. The Nomad Ray includes two pull dumps/OPVs. One is located at the top left on the inside of the wing with a shoulder pull dump using custom molded slides to route the pull cord. The second is located at the bottom outside of the wing, offset to the diver’s left to maintain a low profile back and for easier access when used with multiple cylinders or CCRs.
| Product Category | BCD |
| SKU | DIR-BC4500-XXX |
| Condition | New |
| Brand | Dive Rite |
At Divers Supply you can take advantage of our 60/120 day return policy. You may order just about anything, Inspect the equipment when it arrives, and if you're not fully satisfied you can return it for a full refund (less the shipping charge, for items which we offer free shipping the original shipping savings associated with the returned item(s) will be deducted), as long as you haven't used it. We won't even ask why you've changed your mind.
No restocking fee and no questions asked (provided it has not been used). Items returned within 60 days of date of invoice, will get full refund less S/H charges, Items returned between 60-120 days of date of invoice, will get a full store credit less S/H charges.
To return an item, just follow link below.
Return Merchandise Form
Questions about this item?
Ask us anything, or share you feedback. Our Staff is friendly and knowledgeable and always here to help! We are committed to earning your business with excellent service and prices. Divers Supply has been in business for over 40 years and is always working to give you the best SCUBA gear and equipment at the very lowest prices possible. So chat with one of our Experts and let us help get you into the best gear at the best price!
So, you know what you want but you're on a budget? Or, you've found a lower price somewhere else? Don't worry, we have you covered.
Divers Supply is always working to give you the best SCUBA gear and equipment at the very lowest prices possible. With that, we guarantee to beat any authorized dealers price for the same product!
Another goal of Divers Supply is to fit all of the equipment you need inside your budget. We can not guarantee we can accomplish this, but we will always give it a shot!
Follow the steps below to submit your quote:
We want to make sure we've done everything possible to get you the products you need within your budget. If you found a lower price on an identical item, tell us where.
Add a note with any special requests, shipping instructions, or important product details.
